Chevy Small Block Alum Heads

[BRUTAL64]

Now that I'm building engines again, I"m working deals here and there.


I can get SB Alum heads for the 1st and 2d gen engine for $683.00 to your door. That is my cost.

180 cc intake runner
64 cc chamber.

That is complete ready to run.

This is for Motorgen people.

Yes, these are the same heads that are on the Vette engine in my Avatar.

[Vettezuki]

Now that I'm building engines again, I"m working deals here and there.


I can get SB Alum heads for the 1st and 2d gen engine for $683.00 to your door. That is my cost.

180 cc intake runner
64 cc chamber.

That is complete ready to run.

This is for Motorgen people.

Yes, these are the same heads that are on the Vette engine in my Avatar.

Great deal. You should charge a little more and put some scratch in your pocket, it's still a great deal. Unless your Vette runs on peaches and sunshine. :smack:

[BRUTAL64]

Great deal. You should charge a little more and put some scratch in your pocket, it's still a great deal. Unless your Vette runs on peaches and sunshine. :smack:

Peaches and Sunshine--how did you know?:motorsmile:

[Leedom]

Unless your Vette runs on peaches and sunshine. :smack:

I thought that is what Glen was made of. :rolling:

[Shaolin Crane]

Sure, Glenn is fuzzy like a peach haha

[94cobra69ss396]

I thought that is what Glen was made of. :rolling:

Me too. I thought the Vette ran on rainbows and unicorns.

Glen, is it just SBC heads that you can get or can you get SBF and BBC as well?

[BRUTAL64]

Me too. I thought the Vette ran on rainbows and unicorns.

Glen, is it just SBC heads that you can get or can you get SBF and BBC as well?

Yes I get SBF and BBC heads. Don't know the prices yet. If you are interested I'll talk to them.

[Shaolin Crane]

What brand? Hopefully not procomp :(

[BRUTAL64]

Tri State Racing Cylinder Heads call them "Flow-Tek"s. They machine them in house and I can pick the spings I want.


This is a China cast. Been running mine for 5 years now. All I did was port them some.:ugh:

[Shaolin Crane]

Hmmmm, I was tossong around ideas for a cheap set of heads with an si-trim for the 88, on the other hand, I put the 348 in that car and go ls7 on the 87 :huh:

[Vettezuki]

. . .This is a China cast. Been running mine for 5 years now. All I did was port them some.:ugh:

They may be cast in the same factory as the Avenger heads, which is also the same factory as does some OE Japanese stuff. If so it's a massive, no BS operation; a great value.

[BRUTAL64]

They may be cast in the same factory as the Avenger heads, which is also the same factory as does some OE Japanese stuff. If so it's a massive, no BS operation; a great value.

Get Will's heads this week. Will let you know what I think. Mine have been great not one problem in 5 years.

[BRUTAL64]

Got a price for SBF heads --- same as Chevy--- $685 to my door.:judge:

[BRUTAL64]

Here is some info on the SBF heads;

1.94" intake, 1.54"exhaust stainless swirl polished valves
180cc intake runners
58cc chambers
Hi Performance springs (.550 lift hyd roller)
PC seals
Hardened locks and retainers
High temp exhaust seats
Manganese bronze intake guides phosphor bronze exhaust guides
5 angle valve job

Installation Notes

Head Gasket # M-6051-A50
Intake Gasket # M-9439-A50
Spark Plug # AGSF-32C
Pedestal rockers
Intake Test @ 28" of Water
.100 61.5 CFM
.200 124 CFM
.300 178 CFM
.400 209 CFM
.500 223 CFM
.600 248 CFM

Add to Cart:

Shipping Weight: 80lbs
35 Units in Stock
Manufactured by: Tri-State Cylinder Head

[BRUTAL64]

SBC heads:

New Aluminum Small Block Chevy Heads (pair)

Straight Plug
180cc Intake Runners
64cc Combustion Chambers
Angle or Straight Plug
2.02 and 1.60 Stainless Valves
Performance Springs Good To .550" Lift
5 Angle Valve Job
Bronze Guides
3/8" Screw-In Studs and Guide Plates

Ready For Install



Shipping Weight: 80lbs
96 Units in Stock
Manufactured by: Tri-State Cylinder Head

[94cobra69ss396]

These are what Eric bought for his 331. He's not doing anything to them, he's just going to bolt them on. e'll let you know what we think after it's running.

[BRUTAL64]

These are what Eric bought for his 331. He's not doing anything to them, he's just going to bolt them on. e'll let you know what we think after it's running.

I went and did a little port work. I couldn't just leave them alone.:lmfao:

[BRUTAL64]

Got Will's heads today. They look great. They don't really need any work but I'll do a touch up on the ports.


So far, I have no reservations recommending these heads---not at the price they go for.

[Shaolin Crane]

If they have emissions ports i'd be very interested

[94cobra69ss396]

If they have emissions ports i'd be very interested

Eric's do but they don't have an EO/CARB number. With all the accessories you won't be able to see the heads to know they aren't stock so you should have no problem passing smog. That's what we're counting on with Eric's.

[Shaolin Crane]

The engine will be painted all silver, if I have to I'll engrave a ford part number onto them and steal an afr carb number

[Vettezuki]

The engine will be painted all silver, if I have to I'll engrave a ford part number onto them and steal an afr carb number

I've heard some people have been known to stamp the correct casting numbers on their heads to pass inspections. . . :huh:

[Shaolin Crane]

Yeah that's always an option

[BRUTAL64]

:popcorn:

[Shaolin Crane]

I have a deal working for a set of afr 165's for $400 if it falls through I'll be calling you :D

[BRUTAL64]

I have a deal working for a set of afr 165's for $400 if it falls through I'll be calling you :D

OK.

Ask Ray how the heads look. He came by in his Pantera.

[Shaolin Crane]

Alright, i'll shoot him a text.

[BRUTAL64]

I have a deal working for a set of afr 165's for $400 if it falls through I'll be calling you :D

I called Tri-State- they stated the Ford heads are smog legal. They do not have a Cal smog number, but do have the smog passage.

:pot_stir: