|
|
 |
|
04-28-2010, 06:50 PM
|
#1
|
|
Site Sponsor
InjectorsPlus
Join Date: Feb 2009
Posts: 208
|
MSD 85551 Distributor
Anyone have a problem with an 85551 distributor, I'm not getting an output to my ECU. Before I deem it defective I have some questinos. .
I took the dist apart to lock down the timing advance, put everything back together.
Anything you think I need to look at, I changed over the ignition and ECU in one shot, I am not getting a signal from the distributor to the ECU, I checked pin outs and continuity to the ECU. All seems OK. I can't seem to find a problem
Is it common these distributors have out of box failures?
__________________
|
|
|
|
|
04-28-2010, 09:23 PM
|
#2
|
|
Fast & Filthy
Join Date: Jun 2008
Posts: 3,840
|
I'm running an MSD distributor on both the Chevelle and the Cobra and both worked fine. Are you using an MSD box too?
|
|
|
|
|
04-28-2010, 10:11 PM
|
#3
|
|
Super Moderator
Join Date: Dec 2007
Posts: 6,850
|
I don't like MSD distributors. I had a problem with one, had to send it back in after I found a loose wire when I took it apart, brand new. Their QC needs improvement.
On the dyno it put out intermittent spark. Swapped it out, this one works ok. Although I did just have some ignition problems this last weekend, not sure yet what it is.
|
|
|
|
|
04-28-2010, 10:34 PM
|
#4
|
|
I, Vettezuki
Join Date: Feb 2006
Posts: 14,754
|
I know Glenn is (BRUTAL) is not a fan of MSD.
__________________
Motorgen on
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Motorgen on
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Motorgen Project Car
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(active)
Motorgen Project Car
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(back burner)
|
|
|
|
|
04-28-2010, 11:21 PM
|
#5
|
|
Super Moderator
Join Date: Dec 2007
Posts: 6,850
|
Mallory is like half the cost, next time I'll give them a try.
|
|
|
|
|
04-29-2010, 06:12 AM
|
#6
|
|
Site Sponsor
InjectorsPlus
Join Date: Feb 2009
Posts: 208
|
I am using the MSD 6AL digital programmable box. Here's how it works....the Dist feeds the ECU which, then feeds the MSD 6AL. The ECU is not getting a signal from the distributor.
The way to check the distributor is two fold. ONe is resistance across the coil, which I get, the other is to check AC output of the dist, which should be 300-500 MV. Which it is.
I'm at a loss. Need to call ECU manufacturer. The car FIRES once in the while, rarely. If the MSD isn't giving the signal, nothing else works. Watching the ECU, I'm getting no reading on the RPM gauge. So it's not reading the Distributor.
|
|
|
|
|
04-29-2010, 09:40 AM
|
#7
|
|
Fast & Filthy
Join Date: Jun 2008
Posts: 3,840
|
I don't understand how the 6AL receives an input from the ECU or even how the ECU is involved beside maybe receiving a tach signal from the 6AL. Here's a diagram of how the instructions show it should be connected with the box.
 |
|
|
|
|
04-29-2010, 03:22 PM
|
#8
|
|
Site Sponsor
InjectorsPlus
Join Date: Feb 2009
Posts: 208
|
The ECU accepts the signal from the distributor.
That's the way the system works. This is my first experience with this ECU so I'm trying to figure it out.
Probably something stupid I'm doing, the ECU manufacturer is diligently looking into this.
|
|
|
|
|
04-29-2010, 03:27 PM
|
#9
|
|
Fast & Filthy
Join Date: Jun 2008
Posts: 3,840
|
Quote:
Originally Posted by jsup
The ECU accepts the signal from the distributor.
That's the way the system works. This is my first experience with this ECU so I'm trying to figure it out.
Probably something stupid I'm doing, the ECU manufacturer is diligently looking into this.
|
So you have the green/violet wires from the distributor connected to the ECU and then the ECU connected to the 6AL? |
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
