Home
Don't have an account? Create one now! It's always free!


Forgot Password
Ed's Auto Parts - Mention MOTORGEN for a Discount!
Motorgen Sponsor: McLeod Racing
Motorgen Sponsor: American Muscle - Add style and performance to your Stang
Motorgen Sponsor: Hall Fabrication & Racing
Motorgen Sponsor: Injectors Plus - Performance Fuel Delivery Systems
Reply
Page 6 of 10 « First < 45 6 78 > Last »
 
Thread Tools
Old 11-20-2010, 12:47 PM   #51
94cobra69ss39694cobra69ss396 is offline
Fast & Filthy
 
94cobra69ss396's Avatar
 
Join Date: Jun 2008
Posts: 3,840
Default
Eric and I started assembling his engine last night. We started by removing the sharp edges on the pistons.

Before:



After:



Then we checked the piston to wall clearance on each cylinder using the piston that was going into that cylinder. All were a very tight .005.



We then installed the main bearing and plastigaged the crank mains. All were around .0025. Next we installed a rod and piston and checked the block clearance for the stroker crank. The tightest clearance was .107 so we didn't need to clearance the block at all. We then took it back apart and cleaned everything with soap and warm water and then installed the crank.

Today we are going to plastigage the rod bearings and then assemble the pistons and rods, install the piston rings, and install the pistons. Eric will post up more pictures later.
  Reply With Quote
Old 11-20-2010, 05:32 PM   #52
jedheadjedhead is offline
Senior Member
 
Join Date: Oct 2009
Posts: 1,078
Default
Will removing the material from the pistons require re-balancing?

Bob
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

2003 Honda Accord EX
1973 Datsun 240Z

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
  Reply With Quote
Old 11-20-2010, 05:49 PM   #53
94cobra69ss39694cobra69ss396 is offline
Fast & Filthy
 
94cobra69ss396's Avatar
 
Join Date: Jun 2008
Posts: 3,840
Default
Quote:
Originally Posted by jedhead View Post
Will removing the material from the pistons require re-balancing?

Bob
We didn't remove enough to make a difference in the weight. If we had removed a lot of material then I would have it rebalanced but not with the little we did.

However, we did run into an issue today and I'm glad we did because I discovered I misread the plastigage yesterday. Today we started by installing the pistons on the rods. FYI, full floating pins with Spirolox are a pain the ass to install. Just ask Eric. So after that we checked the bearing clearance and discovered it only had .0015. That's when I realized I misread the Plastigage yesterday when doing the mains. On the mains we only have .0017-.0018. We double checked just to make sure. So we need to get some new bearings that are undersized .001 so that we have the proper clearances. The good news is that we should be able to get them Monday. We also checked the side clearance between the rods which is .0015 so we are good there.
  Reply With Quote
Old 11-24-2010, 02:27 AM   #54
Shaolin CraneShaolin Crane is offline
pain's fun, hit me again
 
Shaolin Crane's Avatar
 
Join Date: Sep 2009
Posts: 6,264
Default
You think those locks are hard to install, try removing them
  Reply With Quote
Old 11-24-2010, 11:31 AM   #55
94cobra69ss39694cobra69ss396 is offline
Fast & Filthy
 
94cobra69ss396's Avatar
 
Join Date: Jun 2008
Posts: 3,840
Default
Quote:
Originally Posted by Shaolin Crane View Post
You think those locks are hard to install, try removing them
No thanks. I'm hoping the engine will last a very long time so it will be years before we have to take them off. Eric was supposed to call CHP Monday about the bearings but he didn't have time so we're on hold right now.
  Reply With Quote
Old 11-24-2010, 04:26 PM   #56
Shaolin CraneShaolin Crane is offline
pain's fun, hit me again
 
Shaolin Crane's Avatar
 
Join Date: Sep 2009
Posts: 6,264
Default
Quote:
Originally Posted by 94cobra69ss396 View Post
No thanks. I'm hoping the engine will last a very long time so it will be years before we have to take them off. Eric was supposed to call CHP Monday about the bearings but he didn't have time so we're on hold right now.
When i put together my old motor i put one of the pistons on backwards, and had a HELL of a time getting the fuckers off
  Reply With Quote
Old 11-24-2010, 08:53 PM   #57
94cobra69ss39694cobra69ss396 is offline
Fast & Filthy
 
94cobra69ss396's Avatar
 
Join Date: Jun 2008
Posts: 3,840
Default
When we checked the piston to wall clearance we numbered each piston with the cylinder we checked it in. Then when we were installing the rods we made sure the rod and piston were facing the correct direction. We also wrote down which rod number was for which cylinder. So I know we won't have to take any apart.

Eric spoke to Coast High Performance today and the Ford engine specialist said that the clearances we had with the plastigage were fine because it isn't very accurate. He said that it usually reads on the tight side and that if we were seeing .0018 with it the clearance was most likely around .0020-.0022. He also told Eric if he was still worried about it that he should take it to a machine shop and have them measure it but that it should be fine. I think Phil has a micrometer that measures ten-thousandths so we'll probably get it from him while he's back for Thanksgiving and then measure it ourselves.
Last edited by 94cobra69ss396 : 11-25-2010 at 12:28 PM.
  Reply With Quote
Old 11-24-2010, 10:38 PM   #58
Shaolin CraneShaolin Crane is offline
pain's fun, hit me again
 
Shaolin Crane's Avatar
 
Join Date: Sep 2009
Posts: 6,264
Default
Oh i did the same thing, even the rods are numbered along with the pistons. Just that one distracted moment and i realized i put the rod in the wrong piston.
  Reply With Quote
Old 07-11-2011, 11:00 AM   #59
94cobra69ss39694cobra69ss396 is offline
Fast & Filthy
 
94cobra69ss396's Avatar
 
Join Date: Jun 2008
Posts: 3,840
Default
Well we haven't updated this in a long time. We ran the bearings as they were and have finished assembling most of the engine. Also, this engine is not going to be NA for a while and Eric is going to add the supercharger at a later time. I dropped the engine in yesterday and we are going to finish it up at the end of this week. Here's how it sits as of yesterday.
  Reply With Quote
Old 07-11-2011, 11:56 AM   #60
Shaolin CraneShaolin Crane is offline
pain's fun, hit me again
 
Shaolin Crane's Avatar
 
Join Date: Sep 2009
Posts: 6,264
Default
Im sure Eric could score a supercharger kit for cheap. They are all over the place right now, i know i scored big time but if he isnt afraid to lowball the shit out of people im sure he can too. What rockers is he running? I know most rockers dont like the stock valve covers.
__________________
Quote:
Originally Posted by Bruce Lee
Forget about winning and losing; forget about pride and pain. Let your opponent graze your skin and you smash into his flesh; let him smash into your flesh and you fracture his bones; let him fracture your bones and you take his life. Do not be concerned with escaping safely — lay your life before him

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Stopping the world!
  Reply With Quote
Reply
Page 6 of 10 « First < 45 6 78 > Last »

« Previous Thread | Next Thread »


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
vB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -7. The time now is 04:46 AM.

Contact Us - Home - Archive - Top