|
|
 |
|
09-23-2012, 01:05 PM
|
#1
|
|
Senior Member
Join Date: Jul 2009
Posts: 122
|
1940 Dodge project update
Hi there MG,
It's Been a while since I rolled out with MG on the 2012 Jan 1st, Tour-d-Orange run. Since then I sold the G37-TT June-2012 and started on the Dodge coupe. Checked it into a shop for fabrication located in Ontario CA. and what a mess that place was. I got out without a scrape money and all, had to send out preliminary summons demand letter to escape with my down payment.
Anyway, found a great fabricator in Riverside "Dukes Roll Cages". So here is some of the upgrade list so far. First bad news was that I pulled out the 440/528 Stroker, it was stock except for the new upgraded parts that could be seen, heads, distributor, intake, etc. all good but the engine was junk, I got lied to that's another story. The Trans appears to be fairly new and in good condition so it's up for sale. So I changed direction from a Twin Turbo 528. Now we are running a 540 Chevy built Bow-Tie motor, built heads and bottom end with a Mooningham 870 blower and dual 980 Holleys with a 700R GM race built trans. Installed on the fabrication build so far are; 14-point chrome molly roll cage tucked into the pillars and hidden in the body structure for a closed tuck job under the interior. The roll cage has removable door and back seat bars for everyday use, and extends into the engine bay attached at 3 points each side. Additional X frame in chrome molly between mid section frame below the drive shaft. New floor pan and trans tunnel, custom aluminum 20 gal fuel cell installed in a new steel basket with a steel bottom impact plate. Tucked battery trays in trunk, and fire wall between rear bench seat. Seats are "Glide" product bolted into the frame. The rear seat has a lift bottom with steel skirt storage. The Currie Third member comes out next week for a check up and upgrade. The new glides for the one piece nose go on next week, military grade slides rated at 1000 lbs. for the pair. I'm still building my dash and installing the steering, Willwood brakes, Vintage Air, electrical, air compressor, glass, interior etc.etc. At this rate I'm probably a good six months out minimum. Posting up a few pics, Take care all hope to roll out with ya-all soon.
|
|
|
|
|
09-23-2012, 05:39 PM
|
#2
|
|
Internet Tough Guy
Join Date: Jun 2008
Posts: 1,545
|
Fucking awesome!
__________________
2007 C6 z51 416ci, KW variant III, Wilwood WS6, Traqmate.
2005 F-350 PSD 4x4 DRW Lariat
2013 Mustang GT Grabber Blue, track pack, Brembo, Recaro, 3.73s
2009 Jetta Auto 2.5 liter
|
|
|
|
|
09-23-2012, 05:42 PM
|
#3
|
|
Senior Member
Join Date: Jul 2009
Posts: 122
|
Very kind, thanks so much, my first total build, LEARNING!!
|
|
|
|
|
09-23-2012, 09:29 PM
|
#4
|
|
pain's fun, hit me again
Join Date: Sep 2009
Posts: 6,264
|
I too was just completely fucked with by a metal fabricator, it's been a year and we're just barely getting the car back tomorrow.
__________________
Quote:
|
Originally Posted by Bruce Lee
Forget about winning and losing; forget about pride and pain. Let your opponent graze your skin and you smash into his flesh; let him smash into your flesh and you fracture his bones; let him fracture your bones and you take his life. Do not be concerned with escaping safely — lay your life before him
|
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Stopping the world!
|
|
|
|
|
09-23-2012, 09:39 PM
|
#5
|
|
Senior Member
Join Date: Jun 2009
Posts: 2,509
|
Well, you're off to a great start that's for sure.
__________________
93 GMC Typhoon: new money pit/PITA. Now GT3788R powered.
Boost, because sometimes atmospheric pressure just isn't enough.
"If it has tit's or tires, you can be pretty sure your going to have problems with them..."
|
|
|
|
|
09-24-2012, 01:20 AM
|
#6
|
|
I, Vettezuki
Join Date: Feb 2006
Posts: 14,754
|
That ought to be fairly ridiculous when complete.
__________________
Motorgen on
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Motorgen on
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Motorgen Project Car
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(active)
Motorgen Project Car
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
(back burner)
|
|
|
|
|
09-24-2012, 06:57 AM
|
#7
|
|
Fast & Filthy
Join Date: Jun 2008
Posts: 3,840
|
Quote:
Originally Posted by BADDASSC6
Fucking awesome!
|
Agreed, that thing is bad ass! |
|
|
|
|
09-27-2012, 04:01 PM
|
#8
|
|
Senior Member
Join Date: Jul 2009
Posts: 122
|
Quote:
Originally Posted by Shaolin Crane
I too was just completely fucked with by a metal fabricator, it's been a year and we're just barely getting the car back tomorrow.
|
Did you get your car back? |
|
|
|
|
09-27-2012, 04:03 PM
|
#9
|
|
Senior Member
Join Date: Jul 2009
Posts: 122
|
Quote:
Originally Posted by Damian
Well, you're off to a great start that's for sure.
|
Thanks, that start line has to be around here somewhere right? |
|
|
|
|
09-27-2012, 04:10 PM
|
#10
|
|
Senior Member
Join Date: Jul 2009
Posts: 122
|
Quote:
Originally Posted by Vettezuki
That ought to be fairly ridiculous when complete.
|
Complete, complete, complete, there's no place like home. |
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
